Audient ASP8024 Dual Layer Control Module Manuel d'utilisateur Page 1

AUTOMATION &CONTROL SURFACEMANUALVersion: 1.00

Page -10-© Audient LtdAutomation SetupWriting and Viewing Automation in LogicOnce setup, rides and mutes can be recorded into Logic and viewed, edited

Page -11-© Audient LtdAutomation SetupHiding Tracks in Logic cont.Please note that Logic is currently the only platform that will happily allow two HU

Page -12-© Audient LtdAutomation Enable / SafeA Note on Automation SafeAutomation safe should be used when you want to isolate a particular channel fr

Control Surface Setup

Page -14-© Audient LtdControl Surface PanelControl Surface OperationThe control surface panel on ASP2802 provides access to many common and useful DAW

Page -15-© Audient LtdControl Surface SetupAssuming that you have followed all steps outlined in the networking section, you will have connected ASP28

Page -16-© Audient LtdStep 2: Install a new HUITM control surface (a 2nd if using one for the fader automation).If using two HUITM controllers(one for

Page -17-© Audient LtdControl Surface SetupStep 4:Close the control surface setup window (top left) and navigate to: Logic Pro > Preferences > C

Page -18-© Audient LtdControl Surface SetupRunning Automation & Control Surfaces Simultaneously Please ensure that there are two banks of 8 channe

Control Surface Functions

Page -2-© Audient LtdASP2802 Fader Automation... Page 3 Automation Overview 4 Automation Se

Page -20-© Audient LtdControl Surface FunctionsEntering DAW LayerTo enter the DAW layer for control surfacefunctionality ensure that the DAW switch (1

Page -21-© Audient LtdControl Surface FunctionsEditing Setup ParametersTo edit parameters in any of the OLED displays when in setup mode, rotate the c

Page -22-© Audient LtdControl Surface FunctionsConsole Setup SwitchSetup Page 3 - IP Address (networking option)Setup Page 4 - Subnet Mask (networking

Page -23-© Audient LtdControl Surface FunctionsTransport PanelThe transport panel on ASP2802 provides access to the following functions:• Rewind (3)•

Page -24-© Audient LtdControl Surface FunctionsTransport Panel cont.By using the scrub function (12) in conjunction with the jog wheel (8), the playhe

Page -25-© Audient LtdControl Surface FunctionsNavigation & Utility Controls cont.The marker control (10) can be used to add markers to the global

Page -26-© Audient LtdNavigation & Utility Controls cont.Track Select ModeRegion Select ModeVertical Zoom ModeHorizontal Zoom ModeTrack Navigation

Page -27-© Audient LtdTrack Navigation Controls cont.To access encoder parameters and / or OLED display information for all eight channels, the 5-8 sw

Page -28-© Audient LtdDAW MetersIf you wish to display eight channels of DAW metering on ASP2802’s LED bargraph meters, a global command switch (17) D

Page -29-© Audient LtdChannel Select ModeThe select mode panel provides various functions, some of which operate on the analogue layer and are useful

Fader Automation

Page -30-© Audient LtdRecord Enable ModeUse record enable (20) within DAW control surface mode when arming tracks for recording in Logic.Activate this

Page -31-© Audient LtdAutomation Modes cont.To access the automation mode selections using the ASP2802 control surface press the automation mode switc

Page -32-© Audient LtdGroup ModeTo access Logic’s internal grouping function press the group mode switch (22) in the select panel.If this is your firs

Page -33-© Audient LtdGroup Mode cont.Unfortunately due to the restriction of the HUITM protocol there is no visual feedback relayed to the ASP2802 OL

Page -34-© Audient LtdControl Surface FunctionsSelect Modes - Analogue Layer cont.Unity - used in the analogue layer to provide a quick and easy way t

Page -35-© Audient LtdControl Surface FunctionsFunction KeysFunction keys F1 to F4 (25) are provided for future expansion of user programmable command

Page -36-© Audient LtdControl Surface FunctionsEncoder Pan ModeWhen selecting pan (27) as the encoder mode on the right hand side of the control surfa

Page -37-© Audient LtdPan Mode + AssignBy pressing the assign key (30) when in pan mode, the encoders provide access to assigning channel inputs and o

Page -38-© Audient LtdPan Mode + Assign cont.Logic I/O labelling can increase the speed of your session setup time. If you have a studio that is setup

Page -39-© Audient LtdControl Surface FunctionsEncoder Aux ModeWhen selecting aux (28) as the encoder mode on the right hand side of the control surfa

Page -4-© Audient LtdAutomationOverview of FunctionsThe diagram below provides an overview of the automation system and the parameters that can be con

Page -40-© Audient LtdControl Surface FunctionsAux / Fader FlipWhen in aux mode pressing the aux switch (28) again will flip the aux send encoders on

Page -41-© Audient LtdControl Surface FunctionsAux Mode + AssignWhen in aux mode, pressing the assign key(30) provides access to instantiating new sen

Page -42-© Audient LtdControl Surface FunctionsInsert ModeThe ASP2802 control surface can be used to instantiate and control insert plugins within Log

Page -43-© Audient LtdControl Surface FunctionsInsert Mode cont.To select a plugin for instantiation, rotate the rotary encoder for the corresponding

Page -44-© Audient LtdInsert Editing ModeTo edit plugin parameters, select the desired plugin with the corresponding encoder (press down). The plugin

Page -45-© Audient LtdFor any future updates to the control surface functionality of ASP2802, please see the ASP2802 webpage and latest firmware avail

Page -46-© Audient LtdPanel Visualisation

www.audient.comAudient Ltd1 Stable CourtHerriard ParkHerriardHampshireRG25 2PLUKPhone: +44 (0) 1256 381944Fax: +44 (0) 1256 381906

Page -5-© Audient LtdAutomation SetupAssuming that you have followed all steps outlined in the mainmanual networking section for Apple Mac (page 84 on

Page -6-© Audient LtdAutomation SetupStep 2: Install a new HUITM control surfaceStep 3:Assign input and outputMIDI ports to ASP2802 Automation

Page -7-© Audient LtdAutomation SetupStep 4: Lock the channel strip view mode to Tracks OnlyStep 5:Close the control surface setup window (top left) a

Page -8-© Audient LtdAutomation SetupStep 6: Return to the arrange page and create 8 new mono “dummy” audio tracks for ASP2802 automation to follow an

Page -9-© Audient LtdAutomation Modes in LogicWe recommend the use of Touch, Latch and Read mode for themajority of your work. Touch mode provides the